午夜福利男女XX00动态图

<span id="nzohj"><blockquote id="nzohj"><b id="nzohj"></b></blockquote></span>
    聯系我們 關于我們

    如何使用剪板機折彎機?


     
    1、首先是接通電源,在控制面板上打開鑰匙開關,再按油泵啟動,這樣你就聽到油泵的轉動聲音了。(此時機器不動作)
    1, the first is the power, in the control panel to open the key switch, and then press the pump to start, so you will hear the sound of the oil pump. (the machine does not move at this time)
    2、行程調節,剪板機折彎機使用必須要注意調節行程,在折彎前要試車。折彎機上模下行至很低部時必須保證有一個板厚的間隙。否則會對模具和機器造成損壞。行程的調節也是有電動快速調整和手動胃調。
    2, stroke adjustment, plate bending machine bending machine use must pay attention to adjust the trip, in the bending before the test must be. The upper die down to the bottom of the bending machine must ensure that there is a gap between the thickness of the plate. Otherwise it will cause damage to the mold and machine. Stroke adjustment is also a fast electric adjustment and manual adjustment of the stomach.
    3、折彎槽口選擇,一般要選擇板厚的8倍寬度的槽口。如折彎4mm的板料,需選擇32左右的槽口。
    3, bending notch, notch in general to choose the thickness 8 times the width of the. Such as plate bending 4mm, need to choose about 32 slot.
    4、后擋料調整一般都有電動快速調整和手動微調,方法同剪板機。
    4, after the adjustment of the material is generally electric fast adjustment and manual adjustment, the same method with plate cutting machine.
    5、踩下腳踏開關開始折彎,剪板機折彎機與剪板機不同,可以隨時松開,松開腳剪板機折彎機便停下,在踩繼續下行。
    5, step on the foot switch to start bending, shear bending machine and plate shearing machine is different, can be at any time to loosen, loosen the foot plate shear bending machine will stop, continue down on the step.
    剪板機折彎機在調試之前要做好以下準備工作,以免機器出現不可挽回的損壞,切記!
    Shear machine bending machine prior to commissioning must be prepared to do the following work, to avoid the emergence of machine irreparable damage, remember!
    (1)操作者在試車前必須詳細閱讀本說明書,熟悉機器的主要結構、性能和使用方法。
    (1) the operator must read the instruction carefully before commissioning and be familiar with the main structure, performance and usage of the machine.
    (2)往油箱內注入32#-16#液壓油,油面達到油標線。
    (2) injection of 32#-16# hydraulic oil into the oil tank, oil to oil line.
    (3)接通電源起動油泵電機,觀察電機轉向是否正確。
    (3) switch on the power supply to start the oil pump motor, and observe whether the motor turn is correct.
    (4)松開遠程調壓閥的手柄(試車時再逐步提高系統的壓力)。
    (4) loosen the handle of the remote pressure regulating valve (and then gradually increase the pressure of the system during commissioning).
    (5)將轉換開關旋到“點動”位置,首先由“點動”開始進行試運行。
    (5) to switch to the "point" position, first by the "point" to start the test run.
    如何使用剪板機折彎機?

    熱門產品

    新的資訊

    午夜福利男女XX00动态图