午夜福利男女XX00动态图

<span id="nzohj"><blockquote id="nzohj"><b id="nzohj"></b></blockquote></span>
    聯系我們 關于我們

    要定期檢修剪板機折彎機的這幾項

    使用剪板機折彎機不能讓機器一直處于滿負荷狀態。而且在經過一段時間的使用以后要對機床進行檢修就像汽車一樣,該保養保養,該換件換件,這樣剪板機才能夠達到很好的使用狀態。
    The use of plate shear bending machine can not let the machine has been in full load condition. And after a period of time after the use of machine tools for maintenance, like a car, the maintenance, the replacement parts, so that the best way to achieve the use of plate shear.
    1、剪板機折彎機的回程缸壓力低時會產生上刀口上升緩慢對回程缸進行充氣。取下保護帽和氣閥帽,裝上充氣工具,充氣工具另一端接氮氣瓶(不得用氧氣),打開充氣工具,緩慢打開氮氣瓶截止閥,注意充氣壓力表。至6.0MPa時立即關閉擔氣瓶截止閥。關閉充氣工具,打開充氣工具,裝上氣閥帽和保護帽。
    The return cylinder pressure, 1 low shear bending machine will produce on the edge of the return cylinder is inflated to rise slowly. Remove the protective cap and air valve cap, fitted with pneumatic tools, the other end of the gas filled with nitrogen gas cylinders (no oxygen), open the gas filling tool, slowly open the valve of the nitrogen gas bottle, pay attention to the gas filled pressure gauge. Turn off the load cylinder stop valve immediately to 6.0MPa. Close the inflation tool, open the inflation tool, install the valve cap and the protective cap.
    2、剪板機折彎機刃口間隙的調整。間隙調整時暫將鎖緊螺釘松開,然后轉動手柄至所需的刻度值,再將螺釘鎖緊。球閥作測量上下刀片刃口間隙均勻度之用。具體方法是以單次行程,當上下架行至下死點時,即迅速轉動球閥關閉油路,使上刀架停于下死點。然后繼續微量開閉球閥,使上刀架在全行程上逐段上升,此時即可逐段測量刃口間隙之均度。
    2, cutting machine bending machine blade gap adjustment. When the gap is adjusted, the locking bolt is loosened, and then the handle is rotated to the required calibration value, and then the screw is locked tightly. Ball valve for measuring the gap between the upper and lower blades edge clearance. Specific method is to a single trip, when the next frame to the bottom dead center is rapidly rotating ball valve turn off the oil, the rest stop to bottom dead center. And then continue to open and close the ball valve, so that the upper tool carrier on the whole trip up, at this time can be measured by cutting edge clearance.
    3、剪板機折彎機油路建立不起壓力,上刀架無動作。電磁換向閥電器插頭接觸不良,檢查電器插頭,電磁換向閥閥芯被雜物卡死或拉毛面不動作。組合閥各閥芯密封口有雜物而不起封閉作用。組合閥內各節流孔阻塞。檢查拆洗。
    3, plate bending machine can not afford to bend the oil pressure, no action on the knife. Electromagnetic reversing valve electrical plug bad contact, check the electrical plug, the electromagnetic reversing valve spool is debris stuck dead or brushed surface does not move. Combination valve of the valve core sealing port with debris and do not play a closed role. Combined valve in the throttle hole blocking. Check and.
    4、剪板機折彎機上刀架回程緩慢或不能回到上死點,上刀架與壓料缸動作順序不協調。分別檢查并加以調整到額定壓力。
    4, shearing machine bending machine tool return slowly or not back to the top dead center, the tool carrier and the pressing cylinder action sequence coordination. Check and adjust to the rated pressure.
    經常對自己使用的剪板機折彎機進行自查可以降低剪板機的故障率。
    Often to their own use of shear bending machine bending machine can effectively reduce the failure rate of plate cutting machine.
    剪板機折彎機定期要檢修哪些項目

    熱門產品

    新的資訊

    午夜福利男女XX00动态图